With the advent of winter, low temperature, dry air-dry, fire-prone. In recent years, all over the garage of the frequent occurrence of fire accidents, fires in winter is high season, these incidents ranging from vehicle emissions and the burning Booth, and around the car, then re-burning vehicle Booth, cars, factories, Cause significant property damage and human casualties. To increase the vehicle maintenance industry on fire safety awareness and large organizations related to the recent Group of professional and technical personnel to conduct market research and visit, opened a garage in winter vehicle Booth fire veil.

     1, a lot of maintenance in the process of baking spray does not establish critical processes, such as baking in a chain of people asked during the fire, always fire, and a lot of maintenance personnel operating in the course of the existence of errors in the formation of a day-to-day production safety problems. Process is not perfect vehicle emissions Booth became one of the sources of fire.

     2, Booth's vehicle heat exchanger material, thickness, size selection is very important in the normal baking, the temperature inside the exchangers is about 1000 ° C, as a whole without leakage. However, many equipment manufacturers a one-sided pursuit of economic efficiency, choice of material, thickness, size does not target the production of raw materials, heat exchangers, such as thickness and size too small, not enough heat-resistant, fire-resistant point only about 700 ° C, and so on, do not consider equipment In the use of possible security risks. Heat exchanger materials do not become the standard vehicle Booth The second source of the fire.

     3, Booth's vehicle burner should be not less than 10 seconds of delay time to sweep chamber, equipped with the ignition off oil overtime protection. Burner maintenance or choose not to become the standard vehicle Booth fire at the source of three.

     4, Booth vehicle should satisfy fans of the wind operation, the air pressure requirements of the induced draft fan should be selected or explosion-proof motor-external, in the course of day-to-day use should be cleaned regularly fan FAN BLADE paint on the paint mist. Fan maintenance or choose not to become the standard vehicle Booth fire at the source of four.

     5, the vehicle of the Housing Lottery Booth steel insulation materials should have a good fire-retardant, thermal insulation, thermal insulation properties, and so many equipment manufacturers use an ordinary color of the plate thermal insulation materials. The failure of the Housing Lottery steel insulation materials into vehicle Booth fire at the source of five.

     6, Booth vehicle should be a special fuel tank, fuel tank and the heating device must be isolated or take appropriate safety measures, not oil Youlou, such as the infiltration occurred, and a lot of repair works were not equipped with special fuel tank, or Private fuel tank directly placed in the bottom of the burner, the oil leak oil all over the floor, the vehicle directly into the source of fire Booth of six.

     7, Booth vehicle electrical components, parts, connectors and wire diameter of the assembly selection is also very important, not pay attention to the power cord, socket, and other components of the security set-up and regular check-ups at random placement or use of aging, thereby Lines open flame caused by a short circuit caused the fire, become a vehicle Booth fire at the source of seven.

     8, Booth vehicle should have the alarm over-temperature protection, heating and air supply system should be interlocking system, the fan broke down, the system should be able to automatically shut down, the lighting system should be a separate fuse or circuit breaker used for short-circuit Protected from electrical appliances to use other protective devices, which have become a vehicle indirectly Booth fire at the source of eight.

     9, Booth vehicle shall be placed around the room and inflammable and explosive materials, many of the operatives of the day-to-day use of paint, thinner, and other organic solvents, by nature lack the necessary knowledge, in particular the lack of chemicals and dangerous goods safety Common sense. Keep combustible materials away from the need to put an end to vehicle emissions is the Booth fire at the source of nine.

     10, Booth vehicle around the room and supporting the use of electrical equipment, we must strengthen the regulation, such as local automotive baking, some manufacturers choose a device similar to the sun's light, its power to reach 1-2 KW, together with non-standard shelter and protection devices, easy to fire. For a variety of machinery and equipment needed to view and debug on a regular basis, the norms of electricity, maximizing happened to contain the fire, which is to eliminate vehicle emissions at the source of fire Booth 10.

     In short, Booth vehicle fires are many reasons to fundamentally eradicate the phenomenon of fire, it requires equipment manufacturers and operators to work together.

     First, manufacturers have to choose regular products, Yanzhua related materials and related accessories, quality and service can only be guaranteed, are determined not to buy in the design and installation of the existence of serious quality problems or safety defects.

     Second, from the day-to-day work of the start of the operators do a good job in pre-job training, to do a good job on a regular basis to maintain and repair equipment on a regular basis to carry out security activities and various security checks.

     Third, it is necessary during the planning workshop facilities, in line with the on-site production design and safety requirements to ensure that all processes do not interfere with each other among the best equipped with special equipment and operators to realize the operation of specialization.

     Fourth, it is necessary to "prevention first, combining anti-consumer" as the guide, equipment specifications, electrical lines, security management, storage, such as the use of inflammable and explosive materials goods safety management responsibility system is in place, to carry out serious self-examination hidden Since the change, without leaving any blind spots, do not stay dead, to eliminate hidden dangers, so that such incidents can not be repeated, to achieve safe production.